收藏本站

ADM1166
POWERING THE ADM1166
The ADM1166 is powered from the highest voltage input on
either the positive-only supply inputs (VPx) or the high voltage
supply input (VH). This technique offers improved redundancy
because the device is not dependent on any particular voltage rail
to keep it operational. The same pins are used for supply fault
detection (see the Supply Supervision section). A V DD arbitrator
on the device chooses which supply to use. The arbitrator can
be considered an OR’ing of five low dropout regulators (LDOs)
together. A supply comparator chooses the highest input to provide
the on-chip supply. There is minimal switching loss with this
architecture (~0.2 V), resulting in the ability to power the ADM1166
from a supply as low as 3.0 V. Note that the supply on the VXx
pins cannot be used to power the device.
In cases where this 12 V supply is hot swapped, it is recommended
that the ADM1166 not be connected directly to the supply. Suitable
precautions, such as the use of a hot swap controller or RC filter
network, should be taken to protect the device from transients
that could cause damage during hot swap events.
When two or more supplies are within 100 mV of each other,
the supply that first takes control of V DD keeps control. For
example, if VP1 is connected to a 3.3 V supply, V DD powers up
to approximately 3.1 V through VP1. If VP2 is then connected to
another 3.3 V supply, VP1 still powers the device, unless VP2
goes 100 mV higher than VP1.
VDDCAP
VP1 IN OUT
4.75V
An external capacitor to GND is required to decouple the on-chip
EN
LDO
supply from noise. This capacitor should be connected to the
VDDCAP pin, as shown in Figure 21. The capacitor has another
use during brownouts (momentary loss of power). Under these
conditions, when the input supply (VPx or VH) dips transiently
VP2
VP3
IN
EN
IN
OUT
4.75V
LDO
OUT
below V DD , the synchronous rectifier switch immediately turns
off so that it does not pull V DD down. The V DD capacitor can
EN
4.75V
LDO
then act as a reservoir to keep the device active until the next
highest supply takes over the powering of the device. A 10 μF
VP4
IN
EN
OUT
4.75V
LDO
capacitor is recommended for this reservoir/decoupling function.
The value of the VDDCAP capacitor may be increased if it is
VH
IN
OUT
4.75V
LDO
INTERNAL
DEVICE
SUPPLY
necessary to guarantee a complete fault record is written into
EEPROM should all supplies fail. The value of capacitor to use
is discussed in the Black Box Writes with No External Supply
section.
The VH input pin can accommodate supplies up to 14.4 V, which
allows the ADM1166 to be powered using a 12 V backplane supply.
Rev. 0 | Page 13 of 32
EN
SUPPLY
COMPARATOR
Figure 21. V DD Arbitrator Operation
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
EVAL-ADM1168LQEBZ BOARD EVAL FOR ADM1168LQ
EVAL-ADM1170EBZ BOARD EVALUATION FOR ADM1170
EVAL-ADM1171EBZ BOARD EVALUATION FOR ADM1171
EVAL-ADM1172EBZ BOARD EVALUATION FOR ADM1172
EVAL-ADM1175EBZ BOARD EVALUATION FOR ADM1175
EVAL-ADM1176EBZ BOARD EVALUATION FOR ADM1176
EVAL-ADM1177EBZ BOARD EVALUATION FOR ADM1177
EVAL-ADM1178EBZ BOARD EVALUATION FOR ADM1178
相关代理商/技术参数
EVAL-ADM1168LQEBZ 功能描述:BOARD EVAL FOR ADM1168LQ RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:* 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081
EVAL-ADM1169LQEBZ 功能描述:BOARD EVAL FOR ADM1169LQ RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:Super Sequencer® 标准包装:1 系列:PSoC® 主要目的:电源管理，热管理 嵌入式:- 已用 IC / 零件:- 主要属性:- 次要属性:- 已供物品:板，CD，电源
EVAL-ADM1170EBZ 功能描述:BOARD EVALUATION FOR ADM1170 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081
EVAL-ADM1171EBZ 功能描述:BOARD EVALUATION FOR ADM1171 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081
EVAL-ADM1172EBZ 功能描述:BOARD EVALUATION FOR ADM1172 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081
EVAL-ADM1175EBZ 功能描述:BOARD EVALUATION FOR ADM1175 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081
EVAL-ADM1176EBZ 功能描述:BOARD EVALUATION FOR ADM1176 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081
EVAL-ADM1177EBZ 功能描述:BOARD EVALUATION FOR ADM1177 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081